Инсталирайте термостатен смесител за душ
Следвайте инструкциите за монтаж стъпка по стъпка, или пуснете видеото, за да видите инсталационния процес.
Подготовка
Спрете водоснабдяването преди да демонтирате стария си смесител.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/05___install_thm_shower/4_3/960/05___install_thm_shower_4_3.jpg)
1 - Ако правите голям ремонт, водната мрежа трябва да бъде прочистена от замърсявания, за да избегнете повреди по смесителя.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-3_4_3/4_3/960/install-thermostatic-shower-mixer-3_4_3_4_3.jpg)
2 - Преди да демонтирате стария си смесител се уверете, че топлата вода е отляво, а студената вода- отдясно. Ако това не е така, повикайте професионалист.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-4_4_3/4_3/960/install-thermostatic-shower-mixer-4_4_3_4_3.jpg)
3- Подгответе нужните части и инструменти.
Подготовка
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-5_4_3/4_3/960/install-thermostatic-shower-mixer-5_4_3_4_3.jpg)
1 - Screw the s union connectors in to your fittings in the wall so that they extend by about 42 mm.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-6_4_3/4_3/960/install-thermostatic-shower-mixer-6_4_3_4_3.jpg)
2 - Монтирайте розетката към стената.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-bath-mixer-7_4_3/4_3/960/install-thermostatic-bath-mixer-7_4_3_4_3.jpg)
3 - Adjust the spacing so that there is 150 mm between the centres of the escutcheons, and then verify they are level . Adjust if necessary.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-8_4_3/4_3/960/install-thermostatic-shower-mixer-8_4_3_4_3.jpg)
4 - Install the mixer and tighten firmly. The nuts must not touch the escutcheons. Adjust if necessary and verify horizontal positioning.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-9_4_3/4_3/960/install-thermostatic-shower-mixer-9_4_3_4_3.jpg)
5 - Dismantle everything. Note the depth between the s union connectors and the wall.
Инсталиране на термостатния смесител
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-10_4_3/4_3/960/install-thermostatic-shower-mixer-10_4_3_4_3.jpg)
1 - Seal the thread of the s union connector using PTFE tape, wrapped in the tightening direction.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-11_4_3/4_3/960/install-thermostatic-shower-mixer-11_4_3_4_3.jpg)
2 - Tighten the s union connectors with a 22 mm open-end wrench.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-12_4_3/4_3/960/install-thermostatic-shower-mixer-12_4_3_4_3.jpg)
3 - Adjust the connectors so that there is a space of 150 mm centre to centre, and the same depth, as noted from your previous measurements. Then check They are level using a spirit level.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-13_4_3/4_3/960/install-thermostatic-shower-mixer-13_4_3_4_3.jpg)
4 - Apply a silicon seal between the wall and the eccentric connectors.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-14_4_3/4_3/960/install-thermostatic-shower-mixer-14_4_3_4_3.jpg)
5 - Screw the escutcheons onto the s union connectors.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-15_4_3/4_3/960/install-thermostatic-shower-mixer-15_4_3_4_3.jpg)
6 - Remove the red and blue caps from the mixer. Make sure the filters are placed correctly, with the rounded side facing inwards.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-16_4_3/4_3/960/install-thermostatic-shower-mixer-16_4_3_4_3.jpg)
7 - Place the mixer on the s union connectors, without adding any additional seals, then tighten the nuts using a 32 mm open-end wrench.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-17_4_3/4_3/960/install-thermostatic-shower-mixer-17_4_3_4_3.jpg)
8 - Използвайте нивелир, за да се уверите, че смесителят е равен. Регулирайте го, ако е необходимо. Проверете за течове, като пуснете водоснабдяването към смесителя.
Настройване на термостатния смесител
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-18_4_3/4_3/960/install-thermostatic-shower-mixer-18_4_3_4_3.jpg)
1 - С помощта на термометър проверете температурата на водата. Ако тя е 38°C, когато показателя на ръкохватката съвпада с показателя за 38°C върху тялото, не е необходима допълнителна настройка.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-19_4_3/4_3/960/install-thermostatic-shower-mixer-19_4_3_4_3.jpg)
2 - Ако се налага допълнителна настройка, запушете отвора за сифона и отстранете горната част на ръкохватките на смесителя с малка плоска отвертка.
2 - If adjustment is necessary, close the water evacuation outlet and remove the cover on the mixer handle using a small flat-head screwdriver. Loosen the screw, then remove the handle.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-20_4_3/4_3/960/install-thermostatic-shower-mixer-20_4_3_4_3.jpg)
3 - Разхлабете винта и отстранете ръкохватката.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-21_4_3/4_3/960/install-thermostatic-shower-mixer-21_4_3_4_3.jpg)
4 - Пуснете водата. Настройте термостатния картуш, чрез завъртане на назъбения черен елемент, докато температурата не достигне 38°C.
Свързване на шлауха
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-22_4_3/4_3/960/install-thermostatic-shower-mixer-22_4_3_4_3.jpg)
Уверете се, че уплътнението в шлауха е на правилното място и завинтете края към смесителя.
Пускане на водата
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/install-thermostatic-shower-mixer-23_4_3/4_3/960/install-thermostatic-shower-mixer-23_4_3_4_3.jpg)
Уверете се, че душ главата работи правилно.
![](http://cdn.cloud.grohe.com/Web/local_assets_4_3/service/fr_fr/final_4_3/4_3/960/final_4_3_4_3.jpg)
Поздравления, готови сте с монтажа на новия си продукт GROHE. Проверете и другите инструкции за инсталация и разгледайте всички наши продукти на grohe.bg