Инсталирайте кухненски смесител с издърпващ се душ
Следвайте инструкциите за монтаж сръпка по стъпка или пуснете видеото и гледайте инсталационния процес.
Подготовка
1 - Ако правите голям ремонт, водната мрежа трябва да бъде прочистена от всякакви замърсявания, за да избегнете повреди по смесителя.
2 - Преди да свалите стария си смесител, се уверете, че топлата вода е отляво, а студената- отдясно. Повикайте професионалист, ако това не е така.
3 - Подгответе нужните части и инстументи.
Инсталиране на горната част на смесителя
1 - Pick up the mixer and water-tight seal. Place the water-tight seal over the two hoses.
2 - Position the water-tight so that it sits securely on the base of the tap and hold it there.
3 - Insert the hoses through the hole in the sink for the mixer.
4 - Place the mixer so that the water-tight seal is in contact with the sink, . Hold the mixer in this position.
5 - Insert the flex hose into the upper part of the high spout.
6 - Then fit the entire spout on to the mixer body.
7 - Use the hoses to hold the mixer firmly until it is attached.
Инсталиране на долната част на смесителя
1 - Place the stabilization ring over the hoses, and then along the threaded rod. Similarly, place the tightening seal and then, lastly, place the tightening nut. Hand-tighten the nut to the maximum.
2 - Release the mixer, which is now held in place, and visually check the mixer's orientation. Adjust it if necessary.
3 - Hold the mixer and use a 17 mm open-end wrench to tighten the nut without forcing.
4 - Under the sink, place one side of the figure-8 shaped ring over the spray hose.
5 - Slide the spring onto the spray hose making sure that the black plastic ends are still in place of the spring
6 - Slide the end of the spray hose through the second figure-8 shaped ring.
7 - Hold the spring and the ring, then screw the hose into the end of the push fit connector.
8 - Slide the push fit connector and lock it into place on the brass rod. Verify that the push connector is correctly fitted by pulling on it.
Пускане на водата
1 - Проверете дали уплатненията в шлауха са поставени правилно. Ако липсват, използвайте филцово или гумено уплътнение. Завинтете шлауха на лявата ръкохватка към изода за топла вода, а шлауха на дясната ръкохватка към извода за студена вода. Затегнете с френски ключ с отворен накрайник 19 mm. Проверете шлауховете за пречупвания и огъвания.
Screw the left-hand hose onto the hot water faucet, and the right-hand hose on the cold water faucet. Tighten with a 19 mm open-end wrench. Make sure there are no kinks or bends in the hoses.
2 - Уверете се, че нищо не пречи на движението на шлауха на издърпващия се душ. Пуснете водоснабдяването и проверете за течове.
3 - Уверете се, че смесителят работи правилно.
Поздравления, готови сте с инсталацията на новия си продукт на GROHE. Проверете останалите инструкции за монтаж и разгледайте всички наши продукти на grohe.bg